How to Reupholster a Chair to Give Your Furniture a Total Refresh

  1. Remove Old Fabric

    Photograph the chair before you strip the original shroud. Take overall and detail photos for address when reupholstering the president .
    disassemble the president as needed and remove the upholstery pieces, taking care not to tear any of the old pieces of fabric—you will need them as patterns. Begin by removing the black fabric from the bottom of the president, then loosen the pieces attached to the frame. Remove the pieces and mark each with its location on the president with a marking playpen. For exercise, label the pieces as outside back, right slope back, left side back, inside back, seat, and seat sides. Mark “ T ” for top or “ F ” for front to indicate the direction of the slice on the president. note on each piece the location of flog and where pieces are sew in concert. Save pieces of welting and tack strips to use as a measure for new pieces .
    Related: Crucial Tips You Need to Know Before You Reupholster Furniture

    Replacing batting on chair
    Jay Wilde

  2. replace Batting

    If worn or stained, remove old bat from professorship back and seat. Check springs and webbing for damage and repair if necessary. Sand, prime, and paint the frame or legs if desired ; let dry .
    Cut a piece of 1/2-inch-thick batting to cover the chair back and buttocks, if needed. Cover the chair back inaugural, stapling it down. To prevent visible indents from the staples, pull gently on the bat around each staple so the staple is inside the bat. next, cover the seat with bat in the same way, folding neatly around the corners .
    Cutting new pattern for chair
    Jay Wilde

  3. Make New Pattern

    Lay the master upholstery pieces wrong-side up on the wrong side of the newly fabric, watching for the grain, placement of the radiation pattern or motifs, and management of the radiation pattern. Pin in place and cut around the pattern, leaving 2 to 3 inches of fabric beyond the staple edges of the original pieces. This will give you fabric to grasp when staple ; the original pieces were trimmed after they were stapled. Repeat this action to cut out each fabric section. Transfer the markings for management, welt, and seams onto the new pieces with chalk .
    If preferred, combine the electric chair reupholstery pieces into covers for the induct and back that can be applied all at once. Place the framework sections together inside out and sew together, adjusting for curves as needed .
    Related: The Ultimate Sewing Guide for Beginners
    Attaching base fabric
    Jay Wilde

  4. Attach Base Fabric

    Place the new inside spinal column, right-side back, and left-side back pieces on the chair in the appropriate locations, using the “ T ” markings and your photos as guides. Pin the pieces together, making any necessary adjustments to the fit ; you may need to trim surfeit fabric to make it fit snugly. When you ‘re please with the meet, pull fabric taut and staple in place on the apron of the chair seat. Use as many staples as necessary to secure the fabric and keep it placid. Be certain you place staples on the moderate back where they will be covered by the back panel. Trim overindulgence fabric. If using a embrace, apply the newfangled blanket to the seat infrastructure and adjust as needed. Pull the fabric taut and raw material to the frame where the old cover was previously attached, starting at the front boundary and working toward the back. Tuck excess framework under at the corners .
    Making welting for chair
    Jay Wilde

  5. Make welt

    Using the old pieces as your guide, determine the distance of the welt needed to go around the seat apron at the top and bottom. Cut enough 2-inch-wide bias strips to equal that distance, allowing a few extra inches. Join the strips with diagonal seams and trim the seam allowance to 1/2 inch. Fold the diagonal deprive around the cord and use a zip up foot to sew in place. The flog will go around the bottom of the seat apron.

    Related: How to Make Welting for Your DIY Chair Upholstery Project
    Sewing welting for chair
    Jay Wilde

  6. Sew Welting

    Pin the side dialog box to the seat fabric, making any necessity adjustments to the fit or pattern placement. Mark the side for the bottom welt. Remove the side fabric from the chair and sew the welt to the right side of the panel, at the top and where marked near the bottom, starting and ending at the back. For a finished edge, fold the conclusion of the piping under before bind .
    Attaching side fabric to chair
    Cutting excess fabric off of chair

    PHOTO: Jay Wilde

    PHOTO: Jay Wilde

  7. Attach Sides

    Holding the correct side of the dialog box up against the seat, staple the top welt in place around the buttocks. Add a tack airstrip around the panel acme against the welt and raw material in target. Fold the side jury down over the stable gear plunder, pull besotted, and staple in place to the bottom of the chair with the bed welting fitting snugly along the edge. Snip notches in the framework underneath the seat as you smooth around corners. Tuck any excess framework underneath using a flathead screwdriver .
    Attaching back fabric to chair
    Jay Wilde

  8. Attach Back

    Place back panel in position and fold the right side over the top of the chair back. Apply a assemble strip to the exceed of the back buttocks and staple in topographic point. Fold the panel back over the strip and pull close toward the bottom of the chair back. Fold bottom edge under and staple to the bottom of the president spinal column. If using a cover for the binding, cutting it over the electric chair back. Pull the fabric tight and staple to the frame where previously attached. Tuck under raw edges where visible. reassemble the chair if needed. Trim any excess string or fabric. Editor’s Tip: Use framework glue or cosmetic upholstery tacks to secure excess fabric to the back of the reupholstered chair .
    Stapling fabric to underside of chair
    Cameron Sadeghpour

  9. Attach Underside to Finish Chair Reupholstery

    Cut a piece of black breathable framework for the bottom of the professorship using the previous nibble as your guide. Flip the electric chair top down, and staple fabric to the bottom to conceal any springs or webbing and dissemble as a dust cover. Make indisputable the framework is tight against the welt and that it covers up all raw edges of the upholstery fabric. Turn right-side up, and enjoy your newly-reupholstered president .

Related Posts

Leave a Reply

Your email address will not be published.