How to Refinish Hardwood Floors

Project details

Skill

3

out of

5

control
Mastering the fender takes some practice

Cost

About $200

Estimated Time

One day

Q: My oak floors are covered in scratches. Do I have to sand down to bare wood to get rid of them ?
—Susan Bankhead, Meridian, Idaho
A: The Editors of This Old House reply: not necessarily. If the scratches do n’t go all the way through to the wood, you can scuff-sand your floors with a buffer and apply a fresh coat or two of complete. The hardwood floor refinishing summons is easier and less expensive than sanding down to bare woodwind and takes less time. In a few hours, your floors will look deoxyadenosine monophosphate good as raw .
The job requires using a buffer, which you can rent at a home center, and a void to suck up scatter. Buffing hardwood floors can be slippery, so if you ‘ve never used a buffer before, exercise in the middle of the room until you get a find for how to maneuver it .
once the finish is roughed up, we put on a water-based polyurethane, which can be recoated in 3 hours. Oil-based polys are cheaper, but each coat takes about 8 hours to dry. With either finish, we recommend a fresh coat every two years or whenever the floor looks wear. Stick to that act and your floors will never wear out .
Pro Tip to Prevent Discoloration: Sometimes the tannins from your wood floor react to water-based polyurethane, causing stain. To avoid this, apply a base coat before applying your water-based poly. Smooth the base coat out evenly around the edges with a paint brush. ( Don ’ t brush excessively flying or you may create bubbles, which will show in the finish. ) Smooth out the stay of the floor with a synthetic floor ending applicator and give your base coat about 2 hours to dry .
here are some extra common questions we ’ ve come across :

How much does it cost to sand and refinish hardwood floors yourself?

If you plan on DIY-ing your hardwood floors, expect to pay a little less than $ 500 per 275 sq. feet. The average roll tends to be between $ 1,000 to $ 2,400 .
The entire cost includes renting sanding equipment along with purchasing sanding pads, wood stain, brushes and finish up .

Is it cheaper to refinish or replace hardwood floors?

You can about constantly bet that refinishing is cheaper than replacing hardwood floors. With the latter, you ’ d be paying not lone for the raw wood but besides for the parturiency of ripping out the old wood and toting it off.

What Are The Steps To Refinishing Hardwood Floors?

Read these 6 steps for refinishing the wood floors in your home :

1. Clean the Floor with a Hardwood Floor Cleaner


Person Using Microfiber Flat Mop On Hardwood Floor

  • Remove all the furniture, and spray the floor with a hardwood flooring cleaner or your own mix of 10 parts water to 1 part white vinegar.
  • Gently wipe the floor with a terry-cloth mop or a towel wrapped around a mop head.
  • Close the windows and doors to keep dust contained in the room you’re sanding.

2. Prep the Perimeter


Man Hand-Sanding Perimeter Of Hardwood Floor With SandPaper

  • Using 180-grit sandpaper, hand-sand the perimeter of the room and any nooks that the buffer can’t reach.
  • Rub with the grain 4 to 6 inches out from the baseboard, working over each board until the finish dulls and a powder forms.

Pro Tip: Do n’t use a sandpaper block for refinishing hardwood—it might miss spotty spots in the floor .

3. Scuff-sand the Floor Finishing


Man Buffering Hardwood Floor

  • Stick a maroon buffing pad to the buffer, and put on a dust mask.
  • Move the buffer from side to side across the floor in the direction of the grain, overlapping each course by 6 inches.
  • The old finish turns to powder as you go, so it’s easy to see the areas you’ve covered.
  • Keep the buffer moving at all times, but stop every 5 minutes or so and vacuum the pad.

4. Vacuum and Tack


Man Dry-Tacking The Floor With Microfiber Cloth

  • Leave the room for 10 to 15 minutes to let the powder settle.
  • Put a clean filter in the vacuum, and sweep the floor using a felt-bottomed attachment.
  • Work in line with the flooring strips, then sweep across them to get any powder that settled between the boards.
  • Finally, dry-tack the floor with a microfiber cloth pushed with the grain.

5. Cut in Along the Edges


Paint Brush Applying Finish Around Corners Of Hardwood Floor

  • Cover your shoes with booties and your nose and mouth with a respirator that has organic vapor canisters.
  • Strain the finish through a cone filter into a clean plastic watering can, minus a sprinkler head, then pour some strained finish into a small plastic container.
  • Brush a 3-inch-wide stripe beside the baseboards at a point farthest from your exit door.
  • You’ll have lap marks if the edge of the stripe starts to dry, so stop after 10 minutes and go to the next step.

6. Roll Out the Poly


Man Using Paint Roller With Extension To Apply Polyurethane On Hardwood Floor

  • Pour out a 1-inch-wide stripe of finish in line with the grain—only as much as you can spread in 10 minutes.
  • Using a long-handled roller with a ¼-inch nap cover, roll out the finish with the grain, then across it.
  • Overlap each pass and work quickly to keep a wet edge.
  • After 10 minutes, brush more finish along the edge, then pour and roll again for 10 minutes. Continue until the floor is covered.
  • Wait 3 hours before recoating and a week before putting back furniture.

Recommended Tools:

Looking for aid with repairs around your home ? A family guarantee may help. Check out these in-depth guides from the This Old House Reviews team :

reservoir : https://epicentreconcerts.org
Category : How To

Related Posts

Leave a Reply

Your email address will not be published.