Dos and Don’ts of Repairing Drywall

Repairing Drywall - Cracked Wall wallboard is tough, but it ’ s not durable. Over meter, gypsum-board walls can sustain despicable cracks or holes. fortunately, wallboard is reasonably easy to repair, but there is an art to it. hera ’ s what to do—and what to avoid—when fixing wallboard damage so it ’ s indiscernible to landlords, homebuyers, or visitors .Repairing Drywall

DO use the right stuff.

When repairing minor scratches or dents smaller than ½ edge across, fill them with a thin layer of joint compound ( besides known as wallboard mud ). Apply using a 3- to 4-inch putty knife made for wallboard work—rather than, say, the kind of narrow-minded utility knife you ’ d use for wood putty—smoothing the filler public treasury it ’ mho flush with the wall. Cracks or holes larger than ½ column inch want reinforce mesh anterior to spackling. If you apply joint compound directly to large gouges, the damage will reappear as the house settles and the joint compound dries and crumbles .

DON’T waste time.

Avail yourself of pre-made products designed to simplify compensate tasks. Patch kits with built center panels and self-adhesive videotape work great for smaller holes. A wallboard compound and flat coat jazz band ( such as 3M Patch Plus Primer, available on Amazon ) leaves a come on that ’ s ready to paint. Find trusted local pros for any home visualize

Find Pros NowHomeAdvisor Logo +BobVila.com Logo

DO remember neatness counts.

Use a box tender or other sharp blade to cut random strands of interlock tape or frayed edges of wallboard paper around holes or cracks before applying joint compound. Otherwise your finished work will show bumps and other blemishes .

DON’T cut the cords.

Be safe and preceptor ’ triiodothyronine hack into a wall to repair a hole until you verify that electric cords and plumbing lines aren ’ metric ton running through the cabinet behind it. If the trap is equitable a few inches wide, shine a flashlight into it to see what ’ sulfur there. If you must enlarge the fix, cautiously cut horizontally with a wallboard saw—but avoid going deeper than an inch. It ’ south safe to assume that hot wires will be present near an electrical mercantile establishment, but don ’ metric ton bet your life—or life savings—that homebuilders or renovators followed all electric and plumbing codes. Wires and pipes are much found where they don ’ t belong .

DO keep it light.

Less is generally more when it comes to joint compound. A thin coat is easier to sand, and you ’ ll be less likely to remove besides much while sanding and expose the bandage. besides, for joint compound to appear flush with the wall near the damage site, “ feather ” the mud as you apply it. Hold the knife at a 70-degree lean, pressing harder on the out edges of the mud as you move away from the center field. ad

DON’T skimp on sanding.

If you cut corners on sandpaper, the repair web site will be obtrusive, so take your fourth dimension. once the animate area is dry, use a fine-grit ( 100 or 120 ) sandpaper. After the first round of sandpaper, add a second layer of mud, spreading it about 2 inches beyond the boundaries of the first layer. once dry, re-sand .

DO use protection.

The ticket particulate of wallboard compound could injure your lungs if inhaled. So always wear a scatter mask when sanding wallboard compound. disposable gloves are besides a estimable estimate to protect your hands from the dehydrating effects of gypsum dust .

DON’T forget to inspect.

Think you ’ re done ? not so fast ! Run your hands over the repair to ensure that it feels legato. then, with your temple against the wall, front for humps that might need more sandpaper.

Repairing Drywall - with Spackle once you ’ re satisfied with the look and feel of your while speculate, premier and paint the sphere. No one will ever know your secret ! ad

Related Posts

Leave a Reply

Your email address will not be published.