How To Drain An Above Ground Pool (In 3 Easy Steps)

First off, let me just say : you should very rarely have to drain your pond at all. In fact, draining it for the winter is not in truth advised because it can cause your liner to dry and crack from the wind and cold. But … there are a few reasons you might have to drain your above ground pool. And if you do have to, there is normally no want to call a pro.

You can identical well do it yourself if you know how.

4 reasons to drain an above ground pool

Some of the reasons you might have to drain your pool include :

  • 1

    thymine o replace the pool liner. This is usually due to a tear or . This is normally ascribable to a tear or leak. There is no getting about draining the pool in this situation ! .

  • 2

    To start the season fresh with new water

    . If you close your pond properly, you shouldn ’ t need to do this, but hey, stuff happens and sometimes, despite our best intentions, we don ’ metric ton get it done … or it doesn ’ t get done properly .

  • 3

    To remove the pool from your yard or replace it

    . ‘Nuff said.

  • 4

    To fix your consortium chemistry due to chlorine engage. Chlorine lock is one of those water conditions that chemicals just can’t fix. In fact, the more chemicals you add, the worse it gets. It’s caused when there is too much pool stabilizer (or cyanuric acid ) in the pool or when the pH levels are unbalanced. It basically renders the chlorine useless and the only way to fix it is to get rid of some of the over-treated water and replace it with fresh water.

How to drain an above ground pool

sale

Superior Pump 91250 1/4 HP Thermoplastic Submersible Utility Pump with 10-Foot Cord

Superior Pump 91250 1/4 HP Thermoplastic Submersible Utility Pump with 10-Foot Cord

  • 1/4 HP Utility pump moves up to 1,800 gallons per hour; pump will lift water up to 25′ of vertical height
  • Tough thermoplastic construction; 10′ cord length

You pretty much have two options when it comes to draining an above anchor pool : you can use a submersible pump, or siphon the water out with a garden hose .
I personally recommend using a combination of the two because siphon is pretty fast, but a pump will help remove that survive foot or then of water that the siphon can ’ t quite get to.

But this is only if you ‘re completely draining it in order to replace the lining. If you ‘re only draining it partially to correct the chemistry, then a garden hose will do the antic without the extra expense.

Step 1. Figure out where to dump the water

Before you start emptying the urine out of your pool, you ‘ll need to figure out where to dump it. You ‘ll need to check with your city to see if there are any especial ordinances governing pool water administration, particularly if you ‘re draining an entire pool : some cities require it to be dumped into the sewage system due to the chemicals.

Step 2. Start a siphon

once you ’ ve decided where the water will go, you can use one of a couple of methods to siphon the water : you can either cut a few feet off each end of a garden hose to create a siphon, or use a complete garden hose and faucet. If you ‘re going to cut your hose, normally a section about 6-8 feet long will do the trick. You ‘ll merely immerse the integral hose in the body of water and then, while covering one end with your hand, promptly pull that end out of the pool and point it downward, below the pool surface. If you choose not to cut the hosiery, you ‘ll need to attach the hosiery to your spigot and fill it completely with water. This works best with two people so that person else can cover the open end of the hosiery to keep body of water from escaping. You can besides use a clamp or crimp the hose with your early hand to keep the urine in.

Step 3. Drain the water

For the discerp hose siphon, you ‘ll just remove your pass once you ‘ve lowered the un-submersed end to the ground and let the water enfeeble. For the entire hose method acting, once the hosiery is full, you ‘ll submerse the hose in the pond and remove the clamp or your hand from the conclusion under the water when there is lone about four feet of hose left above the water. You ‘ll then promptly lower the hose to the land, removing any clamp or cover you have over that end and the water should start flowing through the hose.

Step 4. Remove the remaining water

This step is only for complete drain when you need to replace your liner. There are many ways to do this, but the fastest is to suction it out with a heart or a wet/dry vac. If you merely can ’ thyroxine spare the expense, you can use buckets or other containers to remove deoxyadenosine monophosphate much as you can until it ‘s empty enough to handle. Some water will credibly get dumped in the process, so barely make certain you let it dry out reasonably well before putting in a raw liner so you can prevent bacteria and pool alga from forming under the airfoil.

Bottom line

That ‘s truly all there is to it. If you ‘re alone partially draining your pool, I recommend the cut siphon method just because it ‘s a little easier to handle.

With either method acting, when you ‘ve drained all the craved body of water out, just place the open end back into the pool. Questions ? Comments ? Leave ‘ em below and we ’ ll get back to you right away !

Related Posts

Leave a Reply

Your email address will not be published.